Project Photo Gallery
Please take a few minutes to look through our custom metal fabrication and machined part galleries. These are just a few examples of the product we deliver to our customers.
Click on Any Thumbnail to See an Enlarged View.
The large 220-inch long sheet being rolled using a two-hook lifting system to roll a half circle with a diameter of 172 inches. The material was very light and had to be carefully controlled to ensure the radius was consistent throughout the part length. The material was 0.25 inch thick 316 stainless 2B finish, so extra care was taken to clean the rolls prior to handling.
24-foot x 13.3-foot downdraft system was shipped to Illinois, USA, July 21st to a prestigious client’s showroom. The VeriCUT design along with the customer’s slat frame concept allows lasers to cut with up to 10 kilowatts of power through 2-inch thick steel.
Titanium part with not only folded bends but also multiple radii and complex geometry, showing the variety of bending possible at VeriForm.
New 250 ton x 120 inches long CNC 5-axis press brake.
Image displays step form-roll bending and regular bending combined to create half a clamp for communication towers.
VeriForm uses proprietary bending software to check that your parts fit the machine used for bending the parts, and we even check for collisions. This helps us choose the correct tooling from over $1 million worth of stock brake press tooling we have on hand to bend almost anything your engineers can design.
Totem poles are laser cut from aluminum and rolled for an award show in western North America.
The canoe was made to celebrate Champlain’s landing in Ontario with the body made from Corten steel to prevent long-term rusting. The canoe was designed and welded on-site by Lafontaine Iron Werks.
Stainless 316 grade canopy for a city center fully manufactured by VeriForm for Depco.
24-inch diameter pipe rolled and welded for large open-air structure installation in the USA.
VeriForm uses 300-degree steam cleaning for parts prior to painting, resulting in finished paint that is equivalent or better than sandblasting.
Multiple sheets of steel can be cut on our large 18 foot by 28-foot high definition plasma cutting table built by VeriCUT Inc., our sister division.
Our in-house paint booth allows us to paint up to 20-foot-long parts using any wet paint specification required for the job.
Cutting an access hole in a 54 foot high, 16-inch diameter column for a city center installation. All welds were magnetic particle tested.
Welder-fitters at VeriForm are certified to CWB level 2 welding standards, which allow them to manage and build parts that are structural in nature like bridges and canopies.
The client required the unit to meet +/-0.030 inch tolerances for flatness and VeriForm achieved this, without machining, by using special German-built Demmeler welding tables.
Tiny 15 bend part that fits in the palm of your hand. This is an excellent example of the complexity of tiny parts made at VeriForm.
Laser cut and folded 4mm stainless steel part. This shows off some of the complexity we can handle including inner tabs and odd bend locations.
Fabricated solar panel mount design was optimized by VeriForm engineering staff to allow much lighter material and lower cost while nearly doubling the safety factor of the frame.
A special boring and tapping system creates strong threads in tubing even if they are thin-walled.
Drilling of large and multiple-sized holes into parts. In this setup, it shows the capacity for large diameter drilling in very heavy metal.
2 inch thick round metal shows drilling, tapping, and counterboring all in 1 setup which would not be possible on a lathe.
Really productive and time-saving chuck head shows CNC drilling of round pipe and structurals all in one setup.
Rings can be placed on our CNC machining center and drilled without needing a chuck. This means a fast setup and turnaround time for you!
Heavy-duty truck platform. This shows our ability to manufacture complex and complete assemblies.
Fixture for welding using a special German-built fixturing system that greatly improves the final size integrity and consistency, thereby reducing quality issues.
Welding large assemblies while using a special machine to stress relieve the welding during welding eliminates post-weld stress relieving by up to 95 percent.
Very simple, but large diameter, ring rolling is a good example of basic rolling we can offer.
Simple looking parts, but actually complex, in that the short flanges on these rolled parts are machined legs on a structural angle that we then rolled.
I-beam machined for use in concrete barriers; this is an example of the machining we can perform for you on structural parts.
Deep trough parts requiring a special custom-made gooseneck over 17 feet long which is something very few fab shops are able to do.
Drilling 6 HSS tubes in one setup on 20-foot long machining center save customers time as we produce 6 times the product with just 1 setup.
The large panel being formed on 20-foot long brake press; this shows that we have the capacity to crane large and heavy parts for bending.
CNC-Laser-Cutting of production. Cutting shows parts cleaned and ready to send to our 5 brake presses for bending.
Amazingly complex 21 bend part with non-parallel bends with an employee doing a final check of the part prior to shipping 200 units to a customer.
Large structural panels installed at a train corridor.
13-foot diameter tank shipping out of VeriForm to the customer; ready for use.
Fabricated 32-foot long tank job that included leak testing and 3rd party verification of all welds.
Large panels that were laser cut, formed and welded at VeriForm to be installed in overhead structures.
Truck chain and rigging box designed and built by VeriForm using 5052 and 6061-grade aluminum welded by our CWB certified welders.
Employee checking fit-up of 2 different cone sections rolled for an oven used in the steel mills.
A good example of rolling where we have tapered parts, step formed and combined with smaller semi-cones.
5/8 thick high-strength steel plasma cut, bevelled, and formed is a good example of the high tonnage deep U bending VeriForm can do for you.
Two thick-formed steel parts show off the amazing length we can handle in bending, thereby avoiding welding two shorter, 10-foot pieces together.
Three custom-built tables, built for quick die change applications, complete with adjustable wheel heights and electrical power. Not only can VeriForm build to suit your prints, but we can help with the design to get you more efficient costing based on our experience with what works and what does not.
0.25” thick a572 grade 50 cones step-formed in halves and welded to 3/8” thick a572 grade 50 flat rings. The step-forming is spaced at smaller intervals so that the surface is generally round and smooth with minimal flat regions between each tapered bend compared to cones formed with half the amount of step bends.
Pictured here is a stunning example of the 99% plus capture of the smoke that is created during laser, plasma, and oxy-acetylene cutting DESPITE less than 50% of the table being covered. Nothing on the market compares to the excellent draw of our VeriCUT downdraft tables.
1 minute later and zero smoke. Downdraft tables are workbenches with built-in ventilation systems that capture and draw smoke, fumes and/or dust away from workers and materials being worked on. In this photo, you can see zero smoke because of our unique CrossFlowTM technology that insures there is equal draw across the full width of the cutting table.
The zone-by-zone ducting design means that your dust collection system draws only from the immediate area affected by cutting at that moment, drastically reducing capacity and energy requirements.
A dust collection system is used to enhance the quality of air released from industrial or commercial processes by collecting airborne particles, fine dust particles and impurities.
A downdraft table is a workspace that doubles as a proper waste disposal. There are many health-related hazards that come from breathing in dust and smoke (lung and throat cancer, continuous coughing and sneezing attacks, throat phlegm, asthma, and eye irritation). Therefore, proper dust collection has many good returns on the initial investment
A dust-free environment will result in higher product quality through avoiding rejects, rework, and lost production time. With a good dust collection system, you can breathe easier and enjoy both short and long-term savings!
Built for long, dependable service with lower operating costs. Mechanical zone activation – no expensive electronics, hydraulics or pneumatics with Removable slag trays reduce maintenance downtime by up to 400%.
1/2" 304 Stainless Steel with 0.625” x 1.5” slot. Note the shiny edge quality, ready for welding. Cut with H35 Gas for excellent weldability.
5/8” thick 50W mild steel with 1/2" hole.
1/2" thick Aluminum 6061 Hook.
Celebrating Sustainability in 2020
VeriForm can form any perforated or laser-cut panels into both box-style corrugated and wave-style corrugated even if the panels are made from perforated or laser-cut flat sheets. And we can manufacture the press brake tooling to make any corrugated shape in a matter of days using our unique tooling design that allows micro modification and alteration of the shape to suit your exact design ideas and changes.
VeriForm can use both laser cut or perforated sheets even with larger holes like 0.500” diameter or diamond-shaped cutouts to bend into corrugated waveform and box style type corrugated panels.
